LK Automation Limited
Brand:
OMRON
E5CN-HTR2H01D-FLK Programmed temperature controller
OMRON E5CN-HTR2H01D-FLK Manual And Instructions
E5CN-HTR2H01D-FLK datasheetPDF datasheet
E5CN-HTR2H01D-FLK Programmable TypeUser's Manual
E5CN-HTR2H01D-FLK Programmable TypeBasic Type
E5CN-HTR2H01D-FLK Basic Type
E5CN-HTR2H01D-FLK Basic TypeUser's Manual
E5CN-HTR2H01D-FLK User's Manual
E5CN-HTR2H01D-FLK User's Manual
E5CN-HTR2H01D-FLK Communications FunctionsUser's Manual
E5CN-HTR2H01D-FLK USER'S MANUAL
E5CN-HTR2H01D-FLK Communications FunctionsUser's Manual
E5CN-HTR2H01D-FLK USER'S MANUAL
E5CN-HTR2H01D-FLK INSTRUCTION Manual
OMRON E5CN-HTR2H01D-FLK Product information and technical parameters：
Brand: OMRON
Name: Programmed temperature controller
Model: E5CN-HTR2H01D-FLK
Size: 48 * 48mm, terminal type.
Type: control output 1 point type (power AC/DC24V).
Shell color: black.
Control output: relay output.
Control mode: standard or heating cooling.
Auxiliary output points: 2 points.
Heater break, SSR fault detection function: single phase heater detection function.
Event entry point: 2.
Transfer output: -.
Communication: RS-232C.
New program type.
A new type of liquid crystal with high performance cost ratio is adopted in the 256 paragraph,
Visual angle, contrast can be improved.
Can be set up to 8 procedures (mode) x 32 (step) procedure.
High resolution 5 bit display / can display 0.01 degrees C (to achieve a small size of 48 x 48mm).
High speed sampling period 60ms.
Full of all models (capable of thermocouple /Pt/ analog input switching),
1 machines to support a variety of sensors.
Add PV/SV state display function, to see the state of the thermostat
(automatic / manual, RUN/RESET, alarm),
Interactive display PV/SV.
By supporting software (Ver.4.3 CX-Thermo),
In simple arithmetic functions (AND/OR logic and delay).
Setting the program settings that can perform flexible contact output.
The control output ON/OFF times counting function can predict the fault of the internal relay of the temperature controller.
...More relevant models >>>>
E5CN-HTR2H01D-FLK datasheetPDF datasheet
E5CN-HTR2H01D-FLK Programmable TypeUser's Manual
E5CN-HTR2H01D-FLK Programmable TypeBasic Type
E5CN-HTR2H01D-FLK Basic Type
E5CN-HTR2H01D-FLK Basic TypeUser's Manual
E5CN-HTR2H01D-FLK User's Manual
E5CN-HTR2H01D-FLK User's Manual
E5CN-HTR2H01D-FLK Communications FunctionsUser's Manual
E5CN-HTR2H01D-FLK USER'S MANUAL
E5CN-HTR2H01D-FLK Communications FunctionsUser's Manual
E5CN-HTR2H01D-FLK USER'S MANUAL
E5CN-HTR2H01D-FLK INSTRUCTION Manual
OMRON E5CN-HTR2H01D-FLK Product information and technical parameters：
Brand: OMRON
Name: Programmed temperature controller
Model: E5CN-HTR2H01D-FLK
Size: 48 * 48mm, terminal type.
Type: control output 1 point type (power AC/DC24V).
Shell color: black.
Control output: relay output.
Control mode: standard or heating cooling.
Auxiliary output points: 2 points.
Heater break, SSR fault detection function: single phase heater detection function.
Event entry point: 2.
Transfer output: -.
Communication: RS-232C.
New program type.
A new type of liquid crystal with high performance cost ratio is adopted in the 256 paragraph,
Visual angle, contrast can be improved.
Can be set up to 8 procedures (mode) x 32 (step) procedure.
High resolution 5 bit display / can display 0.01 degrees C (to achieve a small size of 48 x 48mm).
High speed sampling period 60ms.
Full of all models (capable of thermocouple /Pt/ analog input switching),
1 machines to support a variety of sensors.
Add PV/SV state display function, to see the state of the thermostat
(automatic / manual, RUN/RESET, alarm),
Interactive display PV/SV.
By supporting software (Ver.4.3 CX-Thermo),
In simple arithmetic functions (AND/OR logic and delay).
Setting the program settings that can perform flexible contact output.
The control output ON/OFF times counting function can predict the fault of the internal relay of the temperature controller.
Size: 1/4 DIN 96 × 96 × 78 (W × H × D).
Power supply voltage: 100 to 240 VAC.
Input type: Thermocouple or Resistance thermometer.
Alarm output: 3.
Control output: Relay output.
Functions: Heater burnout, Yes (CT1); Mounting option units, Yes.
Previous model: E5AZ-R3 + E53-AZM + E53-AZH.
These Best-selling General,
purpose Temperature Controllers,
Are Now Even Better E5CN-HTR2H01D-FLK.
Controllers now available with analog inputs E5CN-HTR2H01D-FLK
Faster sampling at 250 ms.
Transfer output provided for easy output to recorders.
Models available with a loop break alarm (LBA) and,
heater short alarm (HS alarm).
Manual output provided.
Easy setting with 11-segment displays.
New protocol called Modbus is installed in the,
models with communications E5CN-HTR2H01D-FLK.
USB-Serial conversion cable is available.
Note: Refer to Precautions on page 33. Size: 96 x 96mm.
Category: power AC100 ~ 240V with.
Shell color: black.
Control output 1: position ratio with relay output.
Control output 2: position ratio with relay output.
Control mode: standard or heating cooling.
Auxiliary output points: 2 points.
Heater break, SSR fault detection function: single phase or three phase heater detection function E5CN-HTR2H01D-FLK.
Event entry point: 2.
Transfer output: transfer output (special terminal).
Remote SP:4 to 20mA input.
Communication: RS-485.
New program type.
A new type of liquid crystal with high performance cost ratio is adopted in the 256 paragraph,
Visual angle, contrast can be improved.
Can be set up to 8 procedures (mode) x 32 (step) procedure.
High resolution 5 bit display / can display 0.01 degrees C.
High speed sampling period 60ms.
All models complete a variety of (to the thermocouple /Pt/ analog input switching), 1 machines to support a variety of sensors.
Also supports remote SP.
Add PV/SV state display function, to see the state of the thermostat
(automatic / manual, RUN/RESET, alarm), interactive display PV/SV.
Through the support software (Ver.4.3 CX-Thermo)) makes the process of setting management becomes very
Simple use of simple computing functions (AND/OR logic and delay) to set the implementation of flexible contact output E5CN-HTR2H01D-FLK.
Through the infrared port can be carried out from the frront of the communication E5CN-HTR2H01D-FLK.
The control output ON/OFF times counting function can predict the fault of the internal relay of the temperature controller.
Power supply voltage: 100 to 240 VAC.
Input type: Thermocouple or Resistance thermometer.
Alarm output: 3.
Control output: Relay output.
Functions: Heater burnout, Yes (CT1); Mounting option units, Yes.
Previous model: E5AZ-R3 + E53-AZM + E53-AZH.
These Best-selling General,
purpose Temperature Controllers,
Are Now Even Better E5CN-HTR2H01D-FLK.
Controllers now available with analog inputs E5CN-HTR2H01D-FLK
Faster sampling at 250 ms.
Transfer output provided for easy output to recorders.
Models available with a loop break alarm (LBA) and,
heater short alarm (HS alarm).
Manual output provided.
Easy setting with 11-segment displays.
New protocol called Modbus is installed in the,
models with communications E5CN-HTR2H01D-FLK.
USB-Serial conversion cable is available.
Note: Refer to Precautions on page 33. Size: 96 x 96mm.
Category: power AC100 ~ 240V with.
Shell color: black.
Control output 1: position ratio with relay output.
Control output 2: position ratio with relay output.
Control mode: standard or heating cooling.
Auxiliary output points: 2 points.
Heater break, SSR fault detection function: single phase or three phase heater detection function E5CN-HTR2H01D-FLK.
Event entry point: 2.
Transfer output: transfer output (special terminal).
Remote SP:4 to 20mA input.
Communication: RS-485.
New program type.
A new type of liquid crystal with high performance cost ratio is adopted in the 256 paragraph,
Visual angle, contrast can be improved.
Can be set up to 8 procedures (mode) x 32 (step) procedure.
High resolution 5 bit display / can display 0.01 degrees C.
High speed sampling period 60ms.
All models complete a variety of (to the thermocouple /Pt/ analog input switching), 1 machines to support a variety of sensors.
Also supports remote SP.
Add PV/SV state display function, to see the state of the thermostat
(automatic / manual, RUN/RESET, alarm), interactive display PV/SV.
Through the support software (Ver.4.3 CX-Thermo)) makes the process of setting management becomes very
Simple use of simple computing functions (AND/OR logic and delay) to set the implementation of flexible contact output E5CN-HTR2H01D-FLK.
Through the infrared port can be carried out from the frront of the communication E5CN-HTR2H01D-FLK.
The control output ON/OFF times counting function can predict the fault of the internal relay of the temperature controller.
...More relevant models >>>>